I just ordered a laser engraver/cutter from China. While I wait for the slow boat to come into port, I thought it would be a good idea to start preparing the infrastructure. These products don't include any hardware for the required water-cooling, other than a submersible pump. Most people just say "just have a few gallons of water circulating, and you'll be fine." I say "if it's worth doing, it's worth overdoing."

In the spirit of overdoing it, I remembered that I had a peltier element-cooled fridge in my lab for a while, and that the parts were still kicking around somewhere. Peltier coolers are really neat. They can use an electrical current to drive a thermal energy from one plate to the other. I found an interesting page with a simplified model for calculating their performance across a range of conditions. It's interesting to note that you can't just drive it harder to move more heat; because the modules are consuming energy themselves, self-heating can (and often does) overwhelm the coolers ability to move heat. After spending a couple days understanding the models, I discovered an error in the page, so I'm going to re-post corrected equations.

$T_1 = \frac{-PI+\frac{I^2R_p}{2}+Q_1}{C_1+C_p} + \frac{Q_1+I^2R_p}{C_h} + T_3$

This equation computes the temperature of the "cold side" of the cooler. The model depends on several variables:

$$I$$ = Drive current (Amps)

$$R_p$$ = Cooler resistance from the data sheet (Ohms)

$$Q_1$$ = Thermal load that we're trying to cool (Watts)

$$C_1$$ = Thermal conductivity from load to ambient (Watts/°C)

$$C_p$$ = Thermal conductivity through the peltier (Qmax/ΔTmax) from the data sheet

$$C_h$$ = Thermal conductivity of the heatsink on the hot side (Watts/°C)

$$T_1$$ = Temperature of the object being cooled (°C)

$$T_3$$ = Temperature of the ambient environment (°C)

I'm going to ignore $$P$$. For now, it suffices to say that it's a constant that models the peltier junction's performance: $$\frac{Watts}{Amp}$$

The article that I got this model from doesn't really explain the terms at all, so I'm going to try to interpret the pieces of it. First of all, the $$T_3$$ term references the entire model to ambient. If you used something else as a reference to the peltier you could remove this term and model it another way.

The middle term models the heat flow out of the hot-side heatsink. The numerators of this term are the thermal load (Q1) and the self-heating from the peltier cooler's current (see Ohm's law for the inspiration of this). The entire term is divided by the thermal conductivity of the heatsink, $$C_h$$. Thermal conductivity is a very useful specification, as it tells us the degrees celsius the device will rise per Watt dissipated. In the case of a heatsink, that is referenced to ambient environment.

The first term models the heat flow from the load through the peltier. Again, there is the $$Q_1$$ term, as we have to get the thermal load through the device. Second, we have half of the peltier's self-heating. This is because this model assumes only half of the peltier's self-heating has to travel all the way through the device. Finally, the $$-PI$$ term models the active cooling (the point of this whole thing). These are all divided by the combination of the thermal conductivity of the load-peltier junction and the peltier's internal thermal conductivity.

The upshot of this, is that we can model the performance of our system built around a given peltier junction given load, heatsink performance, and ambient temperature.

$P = \frac{Q+\frac{I^2R_p}{2}}{I}$

Now, let's talk about $$P$$. We can derive $$P$$ entirely from information commonly found in peltier junction datasheets. There really isn't much more to say about this, just plug in the values. The module I'm working with

Now, let's make all of this a little less abstract. The image above is the module that I've salvaged. It's easy enough to lookup the model number and get the data sheet. Using the specification table, directly from the data sheet, we can calculate $$P$$ to be 14.47 (for 25°C). For now, let's also choose some values for the other parameters. Let's say we want to cool a load that is producing 10 Watts, with a rather poor heat sink that has .2 Watt per °C of conductivity (would be listed as 5 °C per Watt as resistance). $T_1 \text{ heat versus amps, with simple heatsink (blue) and ambient (green).}$

If we graph $$T_1$$ versus drive current, $$I$$, we can see that the optimal current from the cooler is 0.8 Amps (red line). Unfortunately, if we compare it to $$\frac{Q_1}{C_h}$$ (which would happen if we just put a heatsink on the load) it's almost 6°C hotter than without the peltier cooler! The laser is estimated to produce about 200 Watts (20 times more than the 10 Watt example) of heat. The problem, ultimately, is that the hot-side heatsink matters. A lot. T1 heat versus amps, with simple heatsink (blue) and ambient (green). With a better heatsink

Now, what happens if we find a much better heatsink They're expensive, but you can find .1 °C per Watt heatsinks on Digi-key. This would be 10 Watts per degree celsius in terms of conductivity. With the better heatsink, the cold side is down to -17 °C! The heat sink is more than able to shunt the heat from the load and the cooler.

$I_{tec}=\frac{PC_h}{R_p(C_h+2(C_1+C_p))}$

All that is obviously super-awesome, but what if we want to calculate what the ideal drive current is for a peltier cooler? The Itec equation, above, will give us this information. We still need the $$P$$ and $$R_p$$ terms from the datasheet, and the thermal conductivity of the peltier and the heatsink. But, you'll notice that thermal load and the ambient temperature are not factors in the equation. Therefore, the ideal drive current (and, therefore maximum temperature drop) are not affected by those factors.

1059 Words

2014-09-08T15:49:24